CAN I INSTALL A BATH TUB MYSELF?

Can I Install A Bath Tub Myself?

Can I Install A Bath Tub Myself?

Blog Article

Request Service

What're your opinions concerning How to Install a Bathtub Yourself?


Tools You Need to Install a New Bathtub
Mounting a bath tub isn't exactly rocket science, but it does need strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can move immediately; if you need to open a wall to eliminate the old bathtub as well as place the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have actually certified on your own for the task as well as fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Chances are you might need a professional plumber to make tube connections.
This article will help you install a brand-new bath tub in your washroom if you have actually currently gotten a brand-new tub as well as don't need to change the arrangement of your previous water supply pipes.
Your devices and also product list must make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installment


    To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to prevent strain on the bath tub.
    Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.

    Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather bothersome because of the limited access that is commonly the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old sealing substance.
    Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

    Setting up the Bath tub


    Using the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
    The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bathtub until the spirit level checks out level.
    To set up taps, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
    Switch on the supply of water as well as inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leaks.
    Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the tub has been utilized a minimum of once as this will settle it right into its last placement.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous type should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, triggering the water to pass through the wall surface between the bathroom and the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into consideration this activity before securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Do you enjoy reading up on Installing A Bathtub? Leave a remark further down. We'd be glad to hear your opinion about this blog posting. We hope that you visit us again soon. Be sure to take the time to share this post if you enjoyed reading it. We thank you for reading our article about Tools You Need to Install a New Bathtub .




    Go Services


    Report this page